Also See for C Operator's manual - 52 pages. Table Of Contents. Quick Links. Table of Contents. Your trimmer has been engineered and manufactured to our high standard for dependability, ease of operation, and opera-. When properly cared for, it will give you years of rugged, trouble-free performance. To reduce the risk of injury, the user must read and understand the operator's manual before using.
Correctement entretenue, elle vous donnera des. Para reducir el riesgo de lesiones,. Previous Page. Next Page. Troubleshooting Troubleshooting 18 Troubleshooting Page 3 Fig. Page 5 Fig. Do not overreach. Read and understand all instructions. When the unit is turned off make sure the cutting instructions. For units equipped with a clutch, be sure attachment has stopped before the unit is set down. Line cutting width C Engine displacement Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.
You can often make adjustments and repairs described here. For other repairs, have the trimmer serviced by an authorized service dealer. If replacing line only, refer to Line Replacement later in this manual. Hold the string head and unscrew the spool retainer. Turn the spool retainer counterclockwise for 26CS. Turn the spool retainer clockwise for 26SS. NOTE: It is not necessary to remove the string head housing from the drive shaft. NOTE: Make sure the arrows on the spool are aligned with the eyelets in the string head housing.
Push down and hold the spool and housing together while completing the installation. Insert the line into the eyelet on the string trimmer housing. Push until the end of the line comes out the other side of the string head. Pull the line from the other side until equal amounts of line appear on both sides of the spool.
Place the insert inside the string head so that the openings on the sides of the insert align with the slots on the sides of the string head. Make sure the spool is completely seated. Line should be pushed in until approximately 1 in. If you notice a power loss with your gas powered tool, you may need to remove these deposits to restore performance.
We highly recommend that only qualified service technicians perform this service. The spark arrestor must be replaced every 50 hours or yearly to ensure proper performance of your product.
Spark arrestors may be in different locations depending on the model purchased. Please contact your nearest service dealer for the location of the spark arrestor for your model. If the cutting attachment turns at idle, the idle speed screw needs adjusting on the engine. Turn the idle speed screw counterclockwise to reduce the idle RPM and stop the cutting attachment movement.
If the cutting attachment still moves at idle speed, contact a service dealer for adjustment and discontinue use until the repair is made. The cutting attachment should never turn at idle. Turn the idle speed screw counterclockwise to reduce the idle RPM and stop the cutting attachment, or contact a service dealer for adjustment and discontinue use until the repair is made.
Serious personal injury may result from the cutting attachment turning at idle. A leaking fuel cap is a fire hazard and must be replaced immediately. If you find any leaks, correct the problem before using the product. Failure to do so could result in a fire that could cause serious personal injury. The fuel cap contains a non-serviceable filter and a check valve. A clogged fuel filter will cause poor engine performance. If performance improves when the fuel cap is loosened, check valve may be faulty or filter clogged.
Replace fuel cap if required. For best performance, engine lubricant should be changed after every 25 hours of operation. Allow the engine to cool completely before proceeding. Remove the bottom cover and set aside. NOTE: Drain the lubricant while the engine is still warm but not hot. Warm lubricant will drain quickly and more completely. Replace the screws and tighten securely.
See your local retailer for more information. Inspect the camshaft-to-rocker arm clearance after every 25 hours of operation. This should be done in a clean, dustfree environment.
NOTE: This procedure requires partial disassembly of the engine. If you are unsure if you are qualified to perform this operation, take the unit to an authorized service center. Remove engine cover and set aside. Remove the cover and set aside. The gap should be between. NOTE: Use a standard automotive feeler gauge. The 0. Take care not to loosen the stud. Once the gap setting is correct, hold the wrench on the flats of the adjusting nut and retighten the retaining nut securely.
Ensure all engine cover and all engine parts are completely and properly reassembled before starting engine. Failure to correctly reassemble engine may result in serious injury or property damage.
Store idle unit indoors in a dry, well-ventilated area that is inaccessible to children. Keep away from corrosive agents such as garden chemicals and de-icing salts. Run engine until it stops. Please have an authorized service center adjust this engine if it is to be run above feet. Failure to do so may result in poor engine performance, spark plug fouling, hard starting, and increased emissions. An engine adjusted for high altitudes can not be run at feet or lower. In doing so, the engine will overheat and cause serious engine damage.
Please have an authorized service center restore high altitude modified engines to the original factory specification before operating below feet. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. S RY Thank you for your purchase.
Merci de votre achat. Le agradecemos su compra. There are measures that can be taken by the operator to possibly reduce the effects of vibration: a Keep your body warm in cold weather. Keep Bystanders Away Keep all bystanders at least 50 ft.
Ricochet Thrown objects can ricochet and result in personal injury or property damage. No Blade Do not install or use any type of blade on a product dis- playing this symbol. Line cutting width C WARNING: To prevent accidental starting that could cause serious personal injury, always disconnect the engine spark plug wire from the spark plug when assembling parts. The attachment connects to the power head by means of a coupler device.
WARNING: Be certain the knob is fully tightened before operating equipment; check it periodically for tightness during use to avoid serious personal injury. There are two ways to hang your attachment for storage. To add engine lubricant:. Lubricant level should fall within the hatched area on the dipstick.
Trimmer should be on a flat, bare surface for starting. For Help Call: Previous Page. Next Page. Ryobi ry string trimmer - engine starting procedure 2 pages. Page 2: Product View C - Coupler coupleur, acoplador D - Power head shaft arbre du bloc moteur, eje del cabezal motor E - Knob bouton, perilla F - Positioning hole trou de positionnement, orificio de posicionamiento G - Trimmer attachment accessoire taille- bordures, aditamento para recortar S Follow all safety instructions.
Failure to follow all safety instructions listed below, can result in serious personal injury. Page 8: Specific Safety Rules Do not use any other cutting attachment. To install any other brand of cutting head to this string trimmer can result in serious personal injury. Page 9: Symbols The following signal words and meanings are intended to explain the levels of risk associated with this product. Please study them and learn their meaning for safe operation of this product.
It is designed for comfort and ease of grasp when operating in different positions and at different angles. Page Operating The Trimmer Do not rest or place your arm, hand, or any body part against the engine housing during trimmer operation.
Only hold the trimmer as shown in Figure 9 with all body parts clear of engine housing. Extended contact with the engine housing may result in burns or other injuries. Proper operating position shown in figure 9. Insert the line into the eyelet on the string trimmer housing. Push until the end of the line comes out the other side of the string head. Line should be pushed in until approximately 1 in.
Inspect the camshaft-to-rocker arm clearance after every 25 hours of operation.
0コメント